--------------------------------------------------------------------------------
Ethernet/IP Adapter V3
--------------------------------------------------------------------------------

V3.3.0.5
--------
 - PSEISV3-153:  DLR functionality shall be disengageable 
 - PSEISV3-156:  [DLR] Device does not handle sign on frames correctly after power up (certification issue) 
 - PSEISV3-157:  [CIP Sync] No synchronization with Rockwell device EN2T/A/B/C (certification issue) 
 - PSEISV3-158:  Update to PTP V2.1.0.2 
 - PSEISV3-159:  [DLR] Transmitted SignOn frame reports an IP address although the address has not been applied by the device at that point in time (certification issue) 


V3.3.0.4
--------
 - PSEISV3-147:  Transmission type is not provided with RCX_GET_DPM_IO_INFO_CNF 
 - PSEISV3-148:  RCX_START_STOP_COMM_REQ does not return RCX_E_INVALID_PARAMETER 
 - PSEISV3-149:  [CIP Sync] Precision Time Protocol does not work 
 - PSEISV3-150:  Update to PTP V2.1.0.1 


V3.3.0.3
--------
 - PSEISV3-145:  Update to LWIP V3.1.0.1 


V3.3.0.2
--------
 - PSEISV3-144:  ACD conflict is still shown after DHCP server assigned new IP adress (certification issue) 


V3.3.0.1
--------
 - PSEISV3-141:  Update to PTP V2.1.0.0 
 - PSEISV3-142:  Get Attribute Single delivers invalid data 


V3.3.0.0
--------
 - PSEISV3-7:  DLR frames are sent with invalid MAC address 
 - PSEISV3-20:  TCP stack is reset when same parameters are set 
 - PSEISV3-26:  Less than 20 user object can be created 
 - PSEISV3-56:  Setting Mcast Config with invalid parameter is not rejected 
 - PSEISV3-60:  Media Counters are not updated 
 - PSEISV3-65:  Active supervisor address is not reset by beacon timeout 
 - PSEISV3-68:  Resource of acyclic communication underflow based on remanante data storage 
 - PSEISV3-76:  Update to TCP/IP V3.0.19.0 
 - PSEISV3-79:  Use 0 as initial sequence number for IO connections and check for a sequence number gap 
 - PSEISV3-94:  COM flag not cleared when limited firmware stops communication after 1 hour 
 - PSEISV3-96:  Stack stops communication when receiving a frame to an unsupported UDP port 
 - PSEISV3-97:  Set Attribute Single to Last Conflict Detected with invalid values possible 
 - PSEISV3-98:  Setting "Interface Label" (Ethernet Link object 0xF6, attribute 10) from host application overwrites internal size of attribute 1 
 - PSEISV3-99:  ACD can be enabled/disabled without reset 
 - PSEISV3-100:  Set Attribute Single to config assembly is forwarded to user application without checking for attribute 3 
 - PSEISV3-101:  Registration of configuration assembly instance returns error TLR_E_EIP_OBJECT_DPM_USED (0xC01F0032) 
 - PSEISV3-102:  Quick Connect attribute is accessible from the network although Quick Connect is not supported 
 - PSEISV3-103:  Stack accepts setting of tcp interface attribute 5 (IP config) when being in DHCP/BOOTP mode (attribute 3) 
 - PSEISV3-104:  [DLR] Flushing MAC address learning table not executed when ring state changes to state "Fault" 
 - PSEISV3-105:  [DLR] Beacon timeout not handled properly when timeout occurrs on both ethernet ports simultaneously 
 - PSEISV3-106:  [DLR] Wrong source port value in Neighbor Check Response frame 
 - PSEISV3-107:  Update TCP/IP Stack to V3.0.22.0 
 - PSEISV3-108:  Update DrvEth component to V1.1.3.0 
 - PSEISV3-109:  [CIP Sync] Time Sync object 0x43 does not support mandatory services Get_Attributes_List and Set_Attributes_List 
 - PSEISV3-110:  Establishing more than 2 input only connections does not work 
 - PSEISV3-111:  [CIP Sync] Attribute 25 of the Time Sync object (0x43) returns an invalid value for "Physical Protocol" 
 - PSEISV3-112:  [EDS] TCP/IP Interface Class revision must be 4 
 - PSEISV3-113:  [ACD] CT12 - Manual ACD test 3.2, 3.5 and 3.8 fail due to AcdStatus bit 6 not being '1' when using DHCP 
 - PSEISV3-114:  No response frame when disabling ethernet port via "Admin State" attribute of Ethernet Link object 
 - PSEISV3-115:  Update to PTP V2.0.2.0 
 - PSEISV3-116:  Ignore Class 0&1 frames with invalid length 
 - PSEISV3-117:  Support interface to host to receive ForwardOpen and ForwardClose service 
 - PSEISV3-119:  Support Interface Capability Attribute 11 of Ethernet Link Object (certification issue) 
 - PSEISV3-122:  Close TCP connection on connection timeout (certification issue) 
 - PSEISV3-124:  Update to LWIP V3.0.25.0 
 - PSEISV3-125:  List Interfaces does not deliver item count (certification issue) 
 - PSEISV3-126:  Update to OSAL V1.0.8.0 
 - PSEISV3-127:  Update to Drv_Eth V1.1.8.0 
 - PSEISV3-128:  Update to PS_Toolbox V1.1.3.0 
 - PSEISV3-129:  Update to netX_Toolbox V1.1.0.1 
 - PSEISV3-130:  Update to rcX_Toolbox V1.1.6.0 
 - PSEISV3-131:  Self test is not executed by reset type 0 
 - PSEISV3-132:  Update to Drv_Eth V1.2.0.0 
 - PSEISV3-133:  NS LED flashing red with cyclic connection 
 - PSEISV3-134:  Unknown Identity Status after Channel Init 
 - PSEISV3-135:  NRP 52-RE: Wrong default device identification with packet configuration 
 - PSEISV3-137:  Cyclic communication interrupted by Set attribute 
 - PSEISV3-139:  Add USB support 
 - PSEISV3-140:  [DLR] Device reports wrong neighbor status information (certification issue) 


V3.2.1.0
--------
 - PSEISV3-7:  DLR frames are sent with invalid MAC address 
 - PSEISV3-20:  TCP stack is reset when same parameters are set 
 - PSEISV3-26:  Less than 20 user object can be created 
 - PSEISV3-56:  Setting Mcast Config with invalid parameter is not rejected 
 - PSEISV3-60:  Media Counters are not updated 
 - PSEISV3-65:  Active supervisor address is not reset by beacon timeout 
 - PSEISV3-68:  Resource of acyclic communication underflow based on remanante data storage 
 - PSEISV3-76:  Update to TCP/IP V3.0.19.0 
 - PSEISV3-79:  Use 0 as initial sequence number for IO connections and check for a sequence number gap 
 - PSEISV3-94:  COM flag not cleared when limited firmware stops communication after 1 hour 
 - PSEISV3-96:  Stack stops communication when receiving a frame to an unsupported UDP port 
 - PSEISV3-97:  Set Attribute Single to Last Conflict Detected with invalid values possible 
 - PSEISV3-98:  Setting "Interface Label" (Ethernet Link object 0xF6, attribute 10) from host application overwrites internal size of attribute 1 
 - PSEISV3-99:  ACD can be enabled/disabled without reset 
 - PSEISV3-100:  Set Attribute Single to config assembly is forwarded to user application without checking for attribute 3 
 - PSEISV3-101:  Registration of configuration assembly instance returns error TLR_E_EIP_OBJECT_DPM_USED (0xC01F0032) 
 - PSEISV3-102:  Quick Connect attribute is accessible from the network although Quick Connect is not supported 
 - PSEISV3-103:  Stack accepts setting of tcp interface attribute 5 (IP config) when being in DHCP/BOOTP mode (attribute 3) 
 - PSEISV3-104:  [DLR] Flushing MAC address learning table not executed when ring state changes to state "Fault" 
 - PSEISV3-105:  [DLR] Beacon timeout not handled properly when timeout occurrs on both ethernet ports simultaneously 
 - PSEISV3-106:  [DLR] Wrong source port value in Neighbor Check Response frame 
 - PSEISV3-107:  Update TCP/IP Stack to V3.0.22.0 
 - PSEISV3-108:  Update DrvEth component to V1.1.3.0 
 - PSEISV3-109:  [CIP Sync] Time Sync object 0x43 does not support mandatory services Get_Attributes_List and Set_Attributes_List 
 - PSEISV3-110:  Establishing more than 2 input only connections does not work 
 - PSEISV3-111:  [CIP Sync] Attribute 25 of the Time Sync object (0x43) returns an invalid value for "Physical Protocol" 
 - PSEISV3-112:  [EDS] TCP/IP Interface Class revision must be 4 
 - PSEISV3-113:  [ACD] CT12 - Manual ACD test 3.2, 3.5 and 3.8 fail due to AcdStatus bit 6 not being '1' when using DHCP 
 - PSEISV3-114:  No response frame when disabling ethernet port via "Admin State" attribute of Ethernet Link object 
 - PSEISV3-115:  Update to PTP V2.0.2.0 
 - PSEISV3-116:  Ignore Class 0&1 frames with invalid length 
 - PSEISV3-117:  Support interface to host to receive ForwardOpen and ForwardClose service 
 - PSEISV3-119:  Support Interface Capability Attribute 11 of Ethernet Link Object (certification issue) 
 - PSEISV3-122:  Close TCP connection on connection timeout (certification issue) 
 - PSEISV3-124:  Update to LWIP V3.0.25.0 
 - PSEISV3-125:  List Interfaces does not deliver item count (certification issue) 
 - PSEISV3-126:  Update to OSAL V1.0.8.0 
 - PSEISV3-127:  Update to Drv_Eth V1.1.8.0 
 - PSEISV3-128:  Update to PS_Toolbox V1.1.3.0 
 - PSEISV3-129:  Update to netX_Toolbox V1.1.0.1 
 - PSEISV3-130:  Update to rcX_Toolbox V1.1.6.0 


V3.2.0.4
--------
 - PSEISV3-115:  Update to PTP V2.0.2.0 
 - PSEISV3-116:  Ignore Class 0&1 frames with invalid length 


V3.2.0.3
--------
 - PSEISV3-97:  Set Attribute Single to Last Conflict Detected with invalid values possible 
 - PSEISV3-98:  Setting "Interface Label" (Ethernet Link object 0xF6, attribute 10) from host application overwrites internal size of attribute 1 
 - PSEISV3-99:  ACD can be enabled/disabled without reset 
 - PSEISV3-100:  Set Attribute Single to config assembly is forwarded to user application without checking for attribute 3 
 - PSEISV3-101:  Registration of configuration assembly instance returns error TLR_E_EIP_OBJECT_DPM_USED (0xC01F0032) 
 - PSEISV3-102:  Quick Connect attribute is accessible from the network although Quick Connect is not supported 
 - PSEISV3-103:  Stack accepts setting of tcp interface attribute 5 (IP config) when being in DHCP/BOOTP mode (attribute 3) 
 - PSEISV3-104:  [DLR] Flushing MAC address learning table not executed when ring state changes to state "Fault" 
 - PSEISV3-105:  [DLR] Beacon timeout not handled properly when timeout occurrs on both ethernet ports simultaneously 
 - PSEISV3-106:  [DLR] Wrong source port value in Neighbor Check Response frame 
 - PSEISV3-107:  Update TCP/IP Stack to V3.0.22.0 
 - PSEISV3-108:  Update DrvEth component to V1.1.3.0 
 - PSEISV3-109:  [CIP Sync] Time Sync object 0x43 does not support mandatory services Get_Attributes_List and Set_Attributes_List 
 - PSEISV3-110:  Establishing more than 2 input only connections does not work 
 - PSEISV3-111:  [CIP Sync] Attribute 25 of the Time Sync object (0x43) returns an invalid value for "Physical Protocol" 
 - PSEISV3-112:  [EDS] TCP/IP Interface Class revision must be 4 
 - PSEISV3-113:  [ACD] CT12 - Manual ACD test 3.2, 3.5 and 3.8 fail due to AcdStatus bit 6 not being '1' when using DHCP 
 - PSEISV3-114:  No response frame when disabling ethernet port via "Admin State" attribute of Ethernet Link object 


V3.2.0.2
--------
 - PSEISV3-76:  Update to TCP/IP V3.0.19.0 
 - PSEISV3-96:  Stack stops communication when receiving a frame to an unsupported UDP port 


V3.2.0.1
--------
 - PSEISV3-5:  Update to TCP/IP V3.0.16.0 
 - PSEISV3-7:  DLR frames are sent with invalid MAC address 
 - PSEISV3-20:  TCP stack is reset when same parameters are set 
 - PSEISV3-26:  Less than 20 user object can be created 
 - PSEISV3-56:  Setting Mcast Config with invalid parameter is not rejected 
 - PSEISV3-60:  Media Counters are not updated 
 - PSEISV3-65:  Active supervisor address is not reset by beacon timeout 
 - PSEISV3-68:  Resource of acyclic communication underflow based on remanante data storage 
 - PSEISV3-75:  Update to TCP/IP V3.0.18.0 
 - PSEISV3-79:  Use 0 as initial sequence number for IO connections and check for a sequence number gap 


V3.2.0.0
--------
 - PSEISV3-16:  [netX52 1Channel] System Reset crashes firmware 
 - PSEISV3-22:  [netX52] Flash device label is not evaluated (Missing MAC address) 
 - PSEISV3-23:  Wrong handling of communication state in common status block 
 - PSEISV3-29:  [NRP52] Flash device label is not evaluated (Missing MAC address) 
 - PSEISV3-42:  Default allocation algorithm for multicast is rejected 
 - PSEISV3-46:  Invalid value for Attributes 8 and 9 of Ethernet Link Object (Class 0xF6, instance 1 and 2) when using packet configuration 
 - PSEISV3-47:  Attribute 1 (Interface speed) of Ethernet Link Object is incorrectly handled on LinkDown 
 - PSEISV3-50:  Identity Reset type 1 does not reset device 
 - PSEISV3-58:  Wrong connection counter value  
 - PSEISV3-70:  Use precompiled distributed OSAL instead of sourcecode 
 - PSEISV3-73:  Use PS_Toolbox V1.1.0.0 
 - PSEISV3-74:  Update to TCP/IP V3.0.13.0 
 - PSEISV3-77:  Use netX and rcX Toolbox 
 - PSEISV3-81:  Update to Drv_Eth V1.0.4.0 
 - PSEISV3-88:  [netX52] CIP Sync Support 
 - PSEISV3-89:  CIP Sync Support: Add CIP Time Sync object (0x43) 
 - PSEISV3-92:  CIP Sync Support: Add handling of packet RCX_SET_HANDSHAKE_CONFIG_REQ 


V3.1.3.0
--------
 - PSEISV3-22:  [netX52] Flash device label is not evaluated (Missing MAC address) 


V3.1.2.0
--------
 - PSEISV3-16:  [netX52 1Channel] System Reset crashes firmware 
 - PSEISV3-29:  [NRP52] Flash device label is not evaluated (Missing MAC address) 


V3.1.1.0
--------
 - PSEISV3-23:  Wrong handling of communication state in common status block 
 - PSEISV3-42:  Default allocation algorithm for multicast is rejected 
 - PSEISV3-46:  Invalid value for Attributes 8 and 9 of Ethernet Link Object (Class 0xF6, instance 1 and 2) when using packet configuration 
 - PSEISV3-47:  Attribute 1 (Interface speed) of Ethernet Link Object is incorrectly handled on LinkDown 
 - PSEISV3-50:  Identity Reset type 1 does not reset device 
 - PSEISV3-58:  Wrong connection counter value  
 - PSEISV3-70:  Use precompiled distributed OSAL instead of sourcecode 
 - PSEISV3-73:  Use PS_Toolbox V1.1.0.0 
 - PSEISV3-74:  Update to TCP/IP V3.0.13.0 
 - PSEISV3-77:  Use netX and rcX Toolbox 
 - PSEISV3-81:  Update to Drv_Eth V1.0.4.0 
 - PSEISV3-88:  [netX52] CIP Sync Support 
 - PSEISV3-89:  CIP Sync Support: Add CIP Time Sync object (0x43) 
 - PSEISV3-92:  CIP Sync Support: Add handling of packet RCX_SET_HANDSHAKE_CONFIG_REQ 


V3.1.0.1
--------
 - PSEISV3-46:  Invalid value for Attributes 8 and 9 of Ethernet Link Object (Class 0xF6, instance 1 and 2) when using packet configuration 
 - PSEISV3-47:  Attribute 1 (Interface speed) of Ethernet Link Object is incorrectly handled on LinkDown 
 - PSEISV3-50:  Identity Reset type 1 does not reset device 
 - PSEISV3-58:  Wrong connection counter value  


V3.1.0.0
--------
 - PSEISV3-44:  RCX_SET_MAC_ADDR_REQ does not work and device starts with MAC 00:00:00:00:00:00 
 - PSEISV3-93:  Update to rcX V2.1.11.2 


V3.0.11.0
---------
 - PSEISV3-87:  [netX52 1Channel] Deactivate clock signals for 2nd XC 


V3.0.10.0
---------
 - PSEISV3-44:  RCX_SET_MAC_ADDR_REQ does not work and device starts with MAC 00:00:00:00:00:00 


V3.0.9.0
--------
 - PSEISV3-2:  Channel Init does not reinitialize Socket API 
 - PSEISV3-9:  DLR: Learning Update Frame not sent 
 - PSEISV3-11:  Set attribute single service to last conflict detection attribute (class 0xF5 attribute 11) is not rejected in case the attribute data is not 35 "00-bytes" 
 - PSEISV3-21:  Support of Attributes 7, 8 and 9 of Ethernet Link Object 
 - PSEISV3-27:  Use a random initial sequence number for IO connections and check for a sequence number gap 
 - PSEISV3-30:  [LFW] Evaluate 2nd Stage Boot token "Custom MMIO mapping" 
 - PSEISV3-39:  Fix port settings and auto mdi does not work 
 - PSEISV3-41:  Update TCP stack to V3.0.12.0 
 - PSEISV3-53:  No link at device without configuration 
 - PSEISV3-59:  Network Connection ID shall not be reused until the connection has been closed or has timed out  
 - PSEISV3-66:  No Forward Close IP address verification 
 - PSEISV3-84:  Support of type 1 reset if no application is registered. 
 - PSEISV3-91:  Support the "Get and Clear" service (0x4C) for the Ethernet Link Object 


V3.0.8.0
--------
 - PSEISV3-13:  TCP settings at database have no effect 
 - PSEISV3-17:  Input data is send with OT RPI 
 - PSEISV3-18:  Connection without configuration assembly may fail to open 
 - PSEISV3-35:  Wrong LED handling 
 - PSEISV3-69:  Update CIP objects without host application 
 - PSEISV3-80:  Support P2P connection input only connection 


V3.0.6.0
--------
 - PSEISV3-4:  LED on netX51 firmware not working 
 - PSEISV3-15:  Wrong dual ported memory size 
 - PSEISV3-19:  duplicate use of command code EIP_APS_CONFIG_DONE_REQ (0x3612) 
 - PSEISV3-28:  IP address is not set with extended configuration method 
 - PSEISV3-32:  Identity Object delivers wrong data 
 - PSEISV3-34:  Data not cleared at dual ported memory when communication is closed 
 - PSEISV3-45:  Set Encapsulation Inactivity Timeout default value 
 - PSEISV3-48:  Input data not updated 
 - PSEISV3-55:  Remanent data is not stored on netX 52 device 
 - PSEISV3-61:  Revision and Product Name not set 
 - PSEISV3-64:  RCX_SET_FW_PARAMETER_REQ does not change expected behaviour 
 - PSEISV3-72:  Wrong "Bus On" behaviour 
 - PSEISV3-78:  LED status after Reset and Power On 


V3.0.5.0
--------
 - PSEISV3-3:  Support firmware for netX52 as single port solution 
 - PSEISV3-49:  Get_Attribute_Single service to I/O object is not handled 
 - PSEISV3-82:  Wrong device class in file header of NRP 52-RE/EIS firmware 
 - PSEISV3-85:  Add EDS for NRP 52-RE/EIS 
 - PSEISV3-86:  Support of NetIdent 


V3.0.4.0
--------
 - PSEISV3-24:  Packets to socket interface are rejected as "unknown command" 
 - PSEISV3-36:  No Link after Configure the Device 


V3.0.3.0
--------
 - PSEISV3-43:  Support of netRapid52 
 - PSEISV3-62:  Support of "Limited Stack" 
 - PSEISV3-63:  Reserved logical segment format not handled 
